I'm excited to finally announce today the availability of a new product by Konnected -- the Konnected Alarm Panel INTERFACE. Available now starting at $99
This new product allows you to connect an existing wired alarm system in parallel with Konnected. This gives you the ability to monitor all of your wired zones in SmartThings, Home Assistant, OpenHAB or Hubitat just like the original Konnected product, but without interfering with the operation of your existing wired alarm.
The new board has special circuitry that lets it tap into any brand of wired alarm system sensor loop without interfering with the existing system. It's designed to be connected in parallel with any type of wired open/close, motion, glass-break or other typical alarm system sensor (except for 2-wire smoke detectors) directly and at any EOL resistance value, therefore the brand or model of panel doesn't matter.
Since the launch of our original Konnected Alarm Panel product a year ago, we've helped convert thousands of wired alarm systems all over the world to smart home systems. However, we heard from a lot of you that you wanted to keep your existing wired alarm and keypads but also wanted to be able to re-use those wired zones for automaton. This product is for you!
This is NOT a replacement or successor to the original Konnected Alarm Panel. It's a new product with a different use case, and we will continue selling and supporting the original Konnected Alarm Panel as well as the new Konnected Alarm Panel INTERFACE for the foreseeable future.
Compare the new Alarm Panel INTERFACE product:
|
Konnected Alarm Panel INTERFACE now available starting at $99 |
Konnected Alarm Panel our original product available here |
|
| Installation method | Connects in parallel to an existing wired alarm system via jumper wires from each zone to the Konnected board. | Completely replaces an existing wired alarm system. Connect sensor wires directly to the Konnected board. |
| Smart Home platforms supported |
SmartThings, Home Assistant, OpenHAB and Hubitat |
SmartThings, Home Assistant, OpenHAB and Hubitat |
| Arming & disarming |
Arm and disarm your existing alarm system as you normally do using the keypads. If your existing system supports it, you may be able to arm & disarm remotely via the Konnected board using a relay and key switch. |
Arm and disarm using your smart home framework. |
| Keypads |
Keep your existing keypads. |
Not compatible with existing keypads. Keypads are not necessary with home automation. Control from your smartphone, voice assistant, or replace the keypads with wall-mounted touchscreen tablets. |
| Professional Monitoring |
Keep your existing pro monitoring service. |
Self-monitor for free with no recurring fees. Noonlight pro monitoring is available on some platforms via smart home integrations. Connect an external communicator with inputs using a relay module. |
| Siren Connection |
No built-in siren connection. It's possible to control the siren via Konnected using the included relay module. |
Built-in connection(s) for most 12V alarm system sirens. |
| Best Choice For |
Your existing alarm system still works, you use it frequently and are happy with it. You want to also use your wired sensors for smart home automation including lighting, HVAC, notifications, etc. |
Your existing wired alarm system either doesn't work, isn't used frequently, or doesn't meet your needs. Or, your home is pre-wired with sensors but no alarm system is installed. You prefer low-cost, convenience, control, and automation over "industry standard" security systems. |
We have a limited quantity from our first production run available now. Due to the busy holiday season, please allow 1 - 2 weeks for processing and shipment. We're doing our best to get all orders out in time for the Christmas holiday, but this isn't guaranteed.
I want to also extend a huge thank you to community member Ben Lebson who was instrumental in the creation of this product, including the design of the hardware and circuitry. Thank you, Ben and welcome to the Konnected team!
Thank you to all the Konnected users out there who have been generous with their feedback, praise and criticism of our technology. Its your passion and excitement that keep us motivated to build more great products like this! Don't be shy with your questions and feedback.
25 comments
Do you plan to integrate with WINK?
I use wink as my primary smart home hub/interface?
Also what if your home wired alarm has some wireless sensors installed? Will they be able to intergrate?
I’m very interested in this product (the new Interface one). Here’s my scenario: I’m cancelling my ADT service shortly due to a number of reasons (mostly annoyed at poor customer service and over-billing issues). As the wired system and keypad were only installed in the last two years, I’d ideally like to be able to keep using this to arm/disarm the system, as well as integrate and monitor through smarthome applications. Would this be the product you guys recommend?
I see you have made a board for the ESP8266, which complier did you use and is your software open source?
Some very good questions in the comments. How about answering them so others don’t have to wonder the same thing. Sounds like a good product.
Does the interface have the ability to use z wave motion sensors to trigger the alarm system?